Boss BRRC27 käyttöohje

Boss BRRC27
(1)
  • Sivuluku: 1
  • Tiedoston tyyppi: PDF
  • THIS PACKAGE CONTAINS
    1 - BRRC27 Soundbar Speaker System
    1 - Bluetooth Multi-Function Controller Kit
    1 - 1.50” Rollbar Mounting Kit
    1 - 1.75” / 2.00” Rollbar Mounting Kit
    1 - Quick Connect Power Cable
    1 - User Manual Quick Start Guide / Poster
    1 - Warranty Card / Facebook Card
    FCC COMPLIANCE STATEMENT
    This device complies with part 15 of the FCC Rules. Operation is subject to the
    following two conditions:
    (1) this device may not cause interference, and
    (2) this device must accept any interference, including interference that may cause
    undesired operation of this device.
    This transmitter must not be co-located or operated in conjunction with any other
    antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by
    user. This equipment complies with FCC/ IC radiation exposure limits set forth for
    an uncontrolled environment and meets the FCC radio frequency (RF) Exposure
    Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
    equipment has very low levels of RF energy that it deemed to comply without
    maximum permissive exposure evaluation (MPE). But it is desirable that it should
    be installed and operated keeping the radiator at least 20 cm or more away from
    person’s body (excluding extremities: hands, wrists, feet and ankles). Alteration
    or modications carried out without appropriate authorization may invalidate the
    user’s right to operate the equipment.
    NOTE: This equipment has been tested and found to comply with the limits for a
    Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-
    signed to provide reasonable protection against harmful interference in a residen-
    tial installation. This equipment generates, uses and can radiate radio frequency
    energy and, if not installed and used in accordance with the instructions, may
    cause harmful interference to radio communications. However, there is no guar-
    antee that interference will not occur in a particular installation. If this equipment
    does cause harmful interference to radio or television reception, which can be
    determined by turning the equipment o and on, the user is encouraged to try to
    correct the interference by one or more of the following measures:
    □ Relocate or reorient the receiving antenna.
    □ Increase the separation between the equipment and receiver.
    □ Connect the equipment into an outlet on a circuit dierent from that to which the
    receiver is connected.
    □ Consult the dealer or an experienced radio/TV technician for help.
    USER MANUAL
    QUICK START GUIDE
    Thank you for purchasing this
    BRRC27 Soundbar Sound System
    Please read through these instructions carefully so you will know
    how to operate your model properly.
    After you have nished reading the instructions, keep this document
    in a safe place for future reference.
    INFORMATION TO THE USERINFORMATION TO THE USER
    The Bluetooth® word mark and logos are registered trademarks owned by
    Bluetooth SIG, Inc. and any use of such marks is under license.
    Other trademarks and trade names are those of their respective owners.
    CAUTION!!
    ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT
    IN HAZARDOUS RADIATION EXPOSURE.
    GETTING TO KNOW YOURBRRC27 MULTIFUNCTION CONTROLLER (MFC)BEFORE YOU STARTIMPORTANT SAFETY PRECAUTIONS
    Do not operate mobile equipment while driving a motorized vehicle – safe driving and
    safety consideration of others should always be your highest priority
    In the event you should notice smoke, strange noises or odor from this product, or any
    other abnormal signs, immediately turn o the power and consult your dealer or the nearest
    authorized BOSS AUDIO Service Center. Using this product in this condition may result in
    permanent damage to the system
    Set your volume control at a low setting, then slowly increase the sound until you can
    hear it comfortably without distortion, or ear discomfort
    BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:
    - Do not turn up the volume so high that you can’t hear what’s around you
    - Use caution or temporarily discontinue use in potentially hazardous situations
    INSTALLATION PRECAUTIONSWARNING - Always consult a professional installer
    Do not attempt to install or service this product by yourself. Installation or servicing of this
    product by persons without professional training and experience in electronic equipment
    and motorized vehicle accessories may be dangerous and could expose you to the risk of
    electric shock, injury or other hazards
    Refer any repairs to a qualied BOSS AUDIO SYSTEMS Service Center
    The BRRC27 should be hard wired directly to the main vehicle battery
    When wiring directly to the vehicles battery, be sure to disconnect the batteries negative
    terminal wire before starting any wiring procedures
    The ground cable length should be short as possible (See wiring diagram)
    The BRRC27 has a weather resistant design, it should not be under any circumstances
    submerged in, or under water
    Use only the supplied installation parts provided with the BRRC27
    Wash with a mild detergent and lukewarm water using a clean sponge or a soft cloth
    Rinse well with clean water
    “DO NOT’S” - Very Important
    DON’T clean in hot sun or on very hot days
    DON’T use abrasive or highly alkaline cleaners on the main body
    DON’T scrape the main body with razor blades, or other sharp instruments
    DON’T ever use, gasoline, acetone or carbon tetrachloride
    DON’T ever use a pressure washer aimed at the speakers
    GETTING STARTED
    A
    1
    2
    3
    4
    5
    6
    7
    8
    9
    MFC - MULTIFUNCTION CONTROLLER
    DOME LIGHT ON/OFF -
    (Auto 10 minute timer when MFC ACC is turned OFF)
    POWER ON - Press and hold for 3 seconds
    EQ - EQ1 | EQ2 | EQ3 | FLAT - EQ1 Default Press and hold for 3 seconds
    NEXT TRACK - FF press and hold
    PLAY/PAUSE - AUX MUTE
    BLUETOOTH PAIRING INDICATOR LED - BLUE / AUX RED COLOR
    PREVIOUS TRACK - FR press and hold
    VOLUME DOWN - Ramp DOWN press and hold
    VOLUME UP - Ramp UP press and hold
    CAUTION!! Using other mounting methods may void this warranty
    PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTION
    1) Power on the MFC by long-pressing the
    3
    Power button for 3 seconds, long-press the
    6
    Bluetooth button for 3 seconds, the BLUE LED will start to rapidly ash, signalling that
    the MFC is now ready for Bluetooth pairing
    NOTE: You have 2 minutes before you must restart this procedure over again.
    2) The MFC is now in pairing mode:
    ANDROID users:
    a. Go into the Settings Menu of your device
    b. Enter the Bluetooth Menu
    c. TURN ON Bluetooth and press SCAN
    d. “BOSS REBEL UTV” will now be displayed under AVAILABLE DEVICES
    e. If prompted, enter passcode: “0000
    iOS users:
    a. Go into the Settings Menu of your iOS device
    b. Enter the Bluetooth Menu
    c. TURN ON Bluetooth
    d. “BOSS REBEL UTV” will now be displayed
    e. If prompted, enter passcode: “0000
    3) If BOSS REBEL UTV is not seen, repeat the above steps to refresh the “Device List”
    4) When the connection is successful a tone will be heard, and the Bluetooth LED indicator
    will light solid, you are now ready to stream music from your favorite media player to the MFC
    Using this product without running the engine can drain the battery.
    To avoid battery exhaustion, be sure to occasionally run the
    vehicles engine while using this product.
    BLUETOOTH OPERATION STREAMING MUSICRECONNECTION
    1) Power on the MFC and your last paired device Bluetooth.
    2) Ensure you are within range of the MFC, the unit will now automatically reconnect
    3) If the device is out of range from the MFC, it will disconnect automatically:
    a. The MFC will reconnect automatically to your device when in range
    4) If your device was previously paired with the MFC, but it wasn’t the last paired device:
    a. Ensure no other devices are currently paired
    b. Enter the Bluetooth Menu on your device being paired
    c. “BOSS REBEL UTV” will display under AVAILABLE DEVICES
    d. Choose the “BOSS REBEL UTV” to reconnect
    5) To clear all previously paired devices from memory, press and hold the MFC Bluetooth
    button for 10 seconds
    NOTE: Some devices may require a manual Bluetooth reconnection once the devices
    Bluetooth is powered OFF / ON and/or back in range, repress the BOSS REBEL UTV
    button in BLUETOOTH settings on your device
    3
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    MULTIFUNCTION CONTROLLER BLUETOOTH OPERATION
    1) Press the
    5
    PLAY/PAUSE once to start playing music or press the PLAY button from
    your devices touch screen
    2) To skip songs or advance, press the
    4
    NEXT TRACK button
    3) To select the previous song, press the
    7
    PREVIOUS TRACK button
    VOLUME CONTROL
    4) To raise the volume press the
    9
    VOLUME UP button or use your devices controls
    5) To lower the volume press the
    8
    VOLUME DOWN button or use your devices controls
    NOTE: If BLUETOOTH or AUX is disconnected for more than 10 minutes the MFC will
    automatically turn OFF, however, when not in use the ACC switch should be manually
    turned OFF to keep the vehicles main battery from draining
    MULTIFUNCTION CONTROLLER AUX-IN OPERATION
    1) Power on the MFC by pressing and holding down the
    3
    POWER button for 3 seconds
    2) Disconnect any paired Bluetooth device by turning o Bluetooth in your devices
    Settings Menu
    3) Connect your 3.5mm AUX-IN cable located on front side of the MFC to your devices
    headphone jack
    4) Route the wire back to MFC, secure your device in a safe location
    VOLUME CONTROL
    5) To raise the volume press the
    9
    VOLUME UP button
    6) To lower the volume press the
    8
    VOLUME DOWN button
    7) To MUTE the volume press the
    5
    PLAY/PAUSE button
    AUX-INPUT
    Make sure your device Bluetooth volume is set at 100% level
    before stowing your device
    BEFORE YOU START INSTALLATION
    Make sure your device headphone volume is set at 100% level
    before stowing your device
    MFC can play audio from
    any device that has a 3.5mm
    headphone audio jack.
    INSERT
    (Cable not included)
    YOUR
    DEVICETips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    MULTI-FUNCTION CONTROLLER MOUNTING
    TOOLS NEEDED:
    - Crimp Tool
    - Wrench or Pliers
    - 3mm Allen Wrench
    MOUNTING THE SOUNDBAR
    When replacing the fuse, be sure to only use a fuse of the rating specied on
    this product. To avoid short-circuiting, cover any disconnected leads with insulating
    tape. It is especially important to insulate any unused wires, which if left uncovered
    may cause a short circuit. When connecting other devices to this product, refer to
    the manual for the product to be connected. The black cable is ground, make sure
    to connect the ground wire rst. Ensure that the ground wire is properly connected
    to metal parts of the vehicles body frame or direct to the battery if your vehicle
    does not have a grounded chassis frame The ground wire of this units power amp
    and a second powered system must be connected to the frame separately with
    dierent screws. If the screw for the ground wire loosens or falls out, it could result
    in re or malfunction.
    To avoid potential shorts in the electrical
    system, be sure to disconnect the (–)
    battery cable before installation. Use this
    unit with a 12-Volt battery and negative
    grounding only. Failure to do so may result
    in a re or malfunction.
    BRRC27RECOIL SERIES BLUETOOTH
    ®
    | 27” AMPLIFIED SOUNDBAR SYSTEMUSER’S MANUALQUICK START GUIDEBRRC27USER’S MANUALRECOIL SERIES27” AMPLIFIED SOUNDBAR SOUND SYSTEMWITH BLUETOOTH REMOTE CONTROLLERPRINTED IN CHINAVER:1.1 ENiPod / iPhone are trademarks of Apple Inc. registered in the U.S. and other countriesAndroid is a trademarks of Google Inc. registered in the U.S. and other countries.BOSS Audio Systems is not aliated with Apple Inc. or Google Inc.
    317
    BOSS Audio Systems3451 Lunar Court • Oxnard, CA 93030www.bossaudio.com | 805-322-8794Tech Support: www.bossaudio.com/support/technical-supportBLUETOOTH • Version: 4.1 • A2DP / AVRCP / GATT • Range: 33ft (10m) Class 2 • 20-Band DSP: 4 Preset EQ • RCA Line Output: 2V RMSSPEAKERS • Dimension: 3.0” • Cone Type: PP CARBON • Tweeter Size: 1” SOFT DOME AMPLIFIER • Maximum Output Power: 500 Watts • Input Impedance: 10kΩ • Frequency Response: 45Hz-25kHzGENERAL • Operational Power: 14.4VDC (10-16V allowable) • MAX Current Draw: 11.7A • USB Charging: 1A @ 5VDC +/- 5% • Replacement Fuse: 15A ATO TYPE • Cabinet Material: Aluminum ExtrusionSPECIFICATIONSWIRE DIAGRAM5.55"(141mm)5.55"(141mm)27"(686mm)4.98"(126.5mm)Dimensions:27" (686mm) x 4.98" (126.5mm) x 5.55" (141mm)Weight:16.53 lbs (7.5 kg)
    15A
    Fuse and fuse holderChassisgroundpointBATTERY Replace with 15A onlyINSERTDIRECT BATTERY WIRING CIRCUIT
    RED
    BLACKChassisgroundpoint
    MFC
    Ground wire
    Metal frame
    ( AUX Cable not included)INSERT
    RED
    BLACKACC SWITCHLINE OUT(-) ORANGE(+) BLUEDOME LIGHTAMP REMOTE INPUTRIGHT
    LEFT
    GROUND
    CRIMPDAISY CHAINLINE OUTPUTSLINE IN(-) MOMENTARY TO ACTIVATE
    3A
    • Color: Black Powder Coating• Weight: 16.53lbs / 7.50kg• Dimensions Inches WxHxD: 27.00 x 4.98 x 5.55• Dimensions cm WxHxD: 68.6 x 12.6 x 14.1• Storage Temperature: 5
    o
    F to 175
    o
    F / -15
    o
    C to 80
    o
    C
    • Operation Temperature: 32
    o
    F to 140
    o
    F / 0
    o
    C to 60
    o
    C
    SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including
    photocopying, recording, or other electronic or mechanical methods, without the prior written permission of BOSS AUDIO Inc.
    Copyright © 2017 BOSS AUDIO Inc.
    BLUETOOTH OPERATIONCAUTION!!
    Mounting brackets should be periodically checked to be sure they are tight
    and secure before use of the vehicle.
    14
    6
    7
    4
    5
    8
    9
    5
    8
    9
    3
    1) Determine the size rollbar for your vehicle, install rubber bushings on rollbar
    2) Insert and align notch of rubber bushings into the aluminum brackets
    3) Apply supplied Loc-Tight to allen bolt tips, let dry for 20 minutes, then align
    the allen bolts and T-nuts into the T-channel, rmly tighten
    4) Recheck all allen bolts are tight, ensure T-nut’s are properly seated in the
    T-channel correctly
    Your Rollbar
    Rubber Bushing
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE5V 1A
    Rubber Bushing
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE5V 1A
    INSTALLATION PARTS
    1.5”
    1.75”
    2”
    RUBBER BUSHINGS
    1.5”
    1.75” or 2”
    BRACKETS
    ROLLBAR / CAGE MOUNT
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE5V 1A
    ALIGN CONNECTOR PINS, INSERT andHAND TIGHTEN
    1.5” 1.75” 2.00”
    FLUSH MOUNT
    SURFACE MOUNT
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    NEVER CONNECT +12V
    TO THE DOME WIRE
    LED DOME - ON/OFFMUTE - ON/OFF STATUS INDICATOR
    WHITE = ON
    RED = STANDBY
    CAUTION:
    NEVER CONNECT THE MFC DIRECTLY
    TO THE BATTERY, ALWAYS USE AN
    ACCESSORY SWITCH
    CAUTION!!
    Never use USB
    or AUX while in
    mud and/or water
    Close USB cover
    when not in use
    5.55"(141mm)5.55"(141mm)27"(686mm)4.98"(126.5mm)Dimensions:27" (686mm) x 4.98" (126.5mm) x 5.55" (141mm)Weight:16.53 lbs (7.5 kg)
    ONBOARD CONTROL PANEL
    Some applications may require
    optional friction tape between
    rubber bushings for a secure,
    tight t, this can be found at
    most local hardware stores
    1) Always check mounting depth before cutting
    2) Use the ush bezel as template
    3) Cutout hole exactly
    4) Insert ush mount bezel, push side tabs outwards
    5) Use optional silicon glue to give extra hold
    6) Insert MFC
    1) Check mounting depth before drilling
    2) Use the ush bezel as template
    3) Drill or cut wire hole exactly
    4) Insert rubber trim around ush bezel,
    screw in place
    5) Insert MFC
    MFC can rotate 90
    o
    for the
    best mounting position
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    3mm Allen Head
    3mm Allen Head
    T-nut must be assembled
    in this conguration
    Align notch
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE5V 1A
    Align notch
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE5V 1A
    OPTIONAL
    OPTIONAL
    OPTIONAL TOOLS NEEDED:
    - Hand saw or Jigsaw
    NOTE!!
    To conserve battery life, the LED Dome light will automatically turn o after
    10 minutes when MFC ACC is turned OFF
    BOSS REFLEX SERIES
    OPTIONAL SYSTEM
    EXPANSIBILITY
    CABLE NOT INCLUDED
    8
    7
    4
    2
    3
    A
    9
    3.5mm AUX-INPUTUSB 1A CHARGING
    NOT FOR AUDIO PLAYBACK
    OPEN
    ALWAYS CLOSE COVER WHEN
    NOT IN USE NEVER USE WHEN
    IN MUD and/or WATER
    Tips:
    EN
    Nyne Cruiser
    USB CHARGE
    5V 1A
    1
    5
    6
    MFC RESET
    LONG PRESS BOSS
    LOGO FOR 10 SECONDS
Boss BRRC27

Tarvitsetko apua?

Kysymysten lukumäärä: 0

Onko sinulla kysyttävää tuotteesta Boss BRRC27 tai tarvitsetko apua? Esitä kysymyksesi täällä. Anna selkeä ja kattava kuvaus asiasta ja kysymyksestäsi. Mitä yksityiskohtaisemmin kuvaat asiaasi ja kysymystäsi, sitä helpompi muiden Boss BRRC27 omistajien on vastata kysymykseesi oikein.

Katso Boss BRRC27 käyttöohjeet täältä ilmaiseksi. Tämä opas kuuluu luokkaan Kaiuttimet, ja sen on arvioinut 1 ihmistä keskimäärin arvosanalla 7.5. Tämä opas on saatavana seuraavilla kielillä: Englanti. Onko sinulla kysyttävää tuotteesta Boss BRRC27 tai tarvitsetko apua? Esitä kysymyksesi täällä

Boss BRRC27 – tekniset tiedot

Yleistä
Tuotemerkki Boss
Malli BRRC27
Tuote Kaiutin
EAN 0601759397399, 0695974869151, 0696552249242, 0791489123655
Kieli Englanti
Tiedoston tyyppi PDF

Usein Kysytyt Kysymykset

Alta löydät useimmin kysytyt kysymykset aiheesta Boss BRRC27.

Eikö kysymystäsi ole listassa? Esitä kysymyksesi täällä