Honeywell RTH230B käyttöohje

Honeywell RTH230B
9.2 · 2
PDF käyttöohje
 · 4 sivua
Englanti
käyttöohjeHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Katso Honeywell RTH230B käyttöohjeet täältä ilmaiseksi. Tämä opas kuuluu luokkaan lämpömittarit, ja sen on arvioinut 2 ihmistä keskimäärin arvosanalla 9.2. Tämä opas on saatavana seuraavilla kielillä: Englanti. Onko sinulla kysyttävää tuotteesta Honeywell RTH230B tai tarvitsetko apua? Esitä kysymyksesi täällä

Tarvitsetko apua?

Onko sinulla kysyttävää aiheesta Honeywell etkä löydä vastausta ohjekirjasta?

  • Saat päivityksiä ratkaisuista
  • Saat vastauksia kysymyksiisi

Kysymys ja vastaus

Kysymysten lukumäärä: 0

Honeywell RTH230B on termostaatti, jonka avulla voit säätää huonelämpötilaa. Termostaattia voidaan käyttää lämmitys- ja jäähdytysjärjestelmissä, ja se voidaan ohjelmoida käynnistymään ja sammumaan automaattisesti tiettynä ajankohtana. Honeywell RTH230B on yksinkertainen ja helppo asentaa, ja sen LCD-näytöltä voit seurata halutun lämpötilan asettamista ja tarkistaa nykyisen lämpötilan. Termostaatti on myös suunniteltu pitkäaikaiseen käyttöön, joten sen käyttö on luotettavaa. Honeywell RTH230B on optimaalinen valinta kodin lämmitys- ja jäähdytysjärjestelmien hallintaan.

Yleistä
TuotemerkkiHoneywell
MalliRTH230B
Tuotelämpömittari
KieliEnglanti
Tiedoston tyyppiKäyttöohje (PDF)

Etkö löydä vastausta kysymykseesi käyttöoppaasta? Saatat löytää vastauksen kysymykseesi UKK-osiosta Honeywell RTH230B alla.

Mikä on paras paikka termostaatin sijoittamiseen?

Paras paikka termostaatille on huone, jossa vietät eniten aikaa, useimmiten olohuone tai keittiö. Aseta termostaatti noin puolitoista metriä lattiapinnan yläpuolelle, ei aurinkoon tai ulkoseinälle.

Mikä on termostaatin kuollut alue?

Jos termostaatissa on kuollut alue, asennus on ikään kuin lepotilassa. Termostaatti kytkeytyy päälle esimerkiksi vain, kun huonelämpötila poikkeaa yli 2 °C asetetusta arvosta.

Mikä on ihanteellinen huonelämpötila?

Useimmista ihmisistä ihanteellinen huonelämpötila on 19–22 astetta.

Onko käyttöohje Honeywell RTH230B saatavilla Suomalainen?

Valitettavasti meillä ei ole käyttöohjetta Honeywell RTH230B saatavilla Suomalainen. Tämä käyttöopas on saatavana seuraavilla kielillä Englanti.

Eikö kysymystäsi ole listassa? Esitä kysymyksesi täällä

Ei tuloksia