Tenda Nova MW5s käyttöohje

Katso täältä ilmaiseksi Tenda Nova MW5s manuaalia. Oletko lukenut manuaalin, mutta se ei vastaa kysymykseesi? Tällöin voit kysyä kysymyksen tällä sivustolla muilta Tenda Nova MW5s omistajilta.

Solid green Good connection
Solid yellow Fair connection
Solid red Disconnected
RST button
RST button
DC power jack to connect to
12 V 1 A power adapter
DC power jack to connect to
9 V 1 A power adapter
WAN/LAN port
WAN/LAN port
LAN port
LAN port
RST
PWRLAN
WAN/LAN
LED indicator
RST
PWRLAN
WAN/LAN
Theprimarynode-Mesh5
Thesecondarynode-Mesh3f
Ethernet jack
Or
DSL
WAN
Modem
Connecting the Primary Node
1. Power off your modem, and remove its battery (if any).
2. Use the included Ethernet cable to connect a LAN port of
your modem or the Ethernet jack to the WAN/LAN port of
the primary node (A label is on its top panel).
3. Re-plug your modem and power it on.
4. Use the 12 V 1 A power adapter to connect the primary node
to a power source, and its LED indicator lights solid green.
Wait for about 40 seconds. The system completes startup
when the LED indicator blinks green.
Connecting the Mobile Device
to the Primary Node
Go to the WiFi network list on your mobile device, select the
SSID of the primary node, and enter its password. The SSID
and password are specified on the bottom label of the
primary node.
1. For the best performance, place each node:
in an elevated, open position with coverage area of your
existing nova WiFi network. This is approximately 20 – 30
feet or 6 – 9 meters between each node.
Keep your nodes away from electrical equipment with
strong interference, such as microwave ovens, induction
cookers and refrigerators.
2. Use the 9 V 1 A power adapters to connect the secondary nodes
to separate power sources, their LED indicators light solid green.
Wait for about 40 seconds. The secondary node is connecting
to another node when its LED indicator blinks green.
Installing the Tenda WiFi App
Download the Tenda WiFi App onto your mobile device by
searching for Tenda WiFi in the App Store/Google Play, or by
scanning the QR code. Then, install the App.
The MW5s consists of one Mesh5 and one or two Mesh3f. The
Mesh5 is the primary node and is used to connect to a modem or
an Ethernet jack, and the Mesh3f is the secondary node used to
extend the WiFi network of the primary node.
Use the 12V 1A power adapter to connect to the primary node while
the 9V 1A power adapters to the secondary nodes for better
stability.
TendaWiFi
Available for iOS and Android
Or
3. When all the nodes are connected, the LED indicators on the
secondary nodes show as follows:
4. If a node's LED indicator does not light solid green, relocate it
according to step 1 in to get a better connection.V 
To access the internet:
- Wired devices: Connect wired devices to the LAN ports of
your nodes.
- Wireless devices: Connect wireless devices to your WiFi
network using the SSID and password you set.
If you want to manage the network anytime, anywhere then
access the App, tap and login to your account.
NOVA_XXXX
XXXXXX
Wi-Fi
12:23PM
CHOOSE A NETWORK...
91%
Settings
Wi-Fi
V
Connecting the Secondary
Nodes to the Internet
Q5: My 2.4 GHz WiFi-enabled devices, such as a home security
camera, cannot connect to my nova WiFi network. What
should I do?
Getting to Know Your Device
Quick Installation Guide
AC1200 Whole Home Mesh WiFi System
MW5s (3-pack)
Internet
Connecting the Primary Node
to the Internet
Run the Tenda WiFi App and follow the on-screen instructions
to connect the primary node to the internet.
After it is connected to the internet, its LED indicator should
turn a solid green.
FAQ
A1: Run the Tenda WiFi App, tap Settings in the lower-right corner,
tap Wireless Settings, change your SSID and password, and tap
Save. After changing your SSID and password, you need to
reconnect your mobile devices using the new SSID and password.
A2: Tap the node on the Tenda WiFi App, tap“...”in the upper-right
corner, and choose Delete.
Note: This removing operation restores the node to factory
settings.
A4: With your nodes powered on, hold the Reset (RST) button of your
primary node down using a reset-pin or a paper clip for about 6
seconds. Release it when the LED indicator blinks fast. Your
network is reset successfully when the LED indicator lights solid
on and then blinks again. And all nodes are then restored to
factory settings.
A3: Yes. Run the Tenda WiFi App, tap Settings in the lower-right
corner, tap Add nova, and follow the on-screen instructions to
add.
Q1: How can I change my SSID and password?
Q2: How can I remove a node from my WiFi network?
Q4: How to restore my network to factory settings?
Q3: Can I add another new set of node to expand my network
coverage?
A5: ( 1 ) Connect your smart phone used for setup to your nova WiFi
network.
(2) Run the Tenda WiFi App, tap Settings, Smart Assistant, and
Enable. Your smart phone connects to the 2.4 GHz WiFi network.
(3) Use the smart phone to set up your 2.4 GHz WiFi-enabled device
guided by the App of the device you would like to connect.
LED indicator description
After a node is powered on, the LED indicator lights solid green for
about 40 seconds to complete startup. Then, the LED indicator lights
one of the following colors:
Node Type
Status
Description
The primary node
Mesh5
Blinking green
Connecting to the internet
Solid green
Connected to the internet
Solid red
Disconnected
The secondary
node
Mesh3f
Blinking green
Connecting to the primary node
Solid green
Good connection.
Solid yellow
Fair connection.
Solid red
Disconnected.
Copyright
© 2018 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda Technology
Co., Ltd. Other brand and product names mentioned herein are trademarks
or registered trademarks of their respective holders. Specifications are
subject to change without notice.
Technical Support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District,
Shenzhen, China. 518052
Operating Environment
Temperature: 0°C-40°C Humidity: (10 - 90)% RH, non-condensing
Adapter Model: BN036-A12012E/BN036-A12012B/BN036-A12012U
Manufacturer: SHENZHEN HEWEISHUN NETWORK
TECHNOLOGY CO., LTD.
Input: 100-240 V AC, 50/60 Hz, 0.4 A
Output: 12 V DC, 1 A
: DC Voltage
CE Mark Warning
This is a Class B product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to take
adequate measures.
Operations in the 5.15-5.25GHz band are restricted to indoor use only.
This equipment should be installed and operated with a minimum
distance 20cm between the device and your body.
Declaration of Conformity
Hereby, Shenzhen Tenda Technology Co., Ltd. declares that the radio
equipment type Mesh5 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:
http://www.tendacn.com/en/service/download-cata-101.html
NOTE: ( ) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
(2) To avoid unnecessary radiation interference, it is recommended to
use a shielded RJ45 cable.
WARNING: The mains plug is used as disconnect device; the disconnect
device shall remain readily operable.
1
FCC Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Caution:
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Operating frequency: 2412-2462MHz, 5150-5250MHz, 5725-5850MHz
The device is for indoor usage only.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC
RF Rules.
This equipment should be installed and operated with a minimum
distance 20cm between the device and your body.
Caution:
Adapter Model: BN052-A09009U/BN052-A09009E/BN052-A09009B
Manufacturer: SHENZHEN HEWEISHUN NETWORK
TECHNOLOGY CO., LTD.
Input: 100-240 V AC, 50/60 Hz, 0.3 A
Output: 9 V DC, 1 A
: DC Voltage
Caution:
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be
RECYCLING
Declaration of Conformity
Hereby, Shenzhen Tenda Technology Co., Ltd. declares that the radio
equipment type Mesh3f is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:
http://www.tendacn.com/en/service/download-cata-101.html
For EU/EFTA, this product can be used in the following countries:
caused by unauthorized modifications to this equipment. (2) To avoid
unnecessary radiation interference, it is recommended to use a shielded
RJ45 cable.
NOTE:
(1) The manufacturer is not responsible for any radio or TV interference
Hong Kong hotline: 00852-81931998
Website: http://www.tendacn.com
Email: support.nova@tenda.com.cn
Canada hotline: 1-888-998-8966
Toll Free: Mon - Fri 9 am - 6 pm PST
Operating Frequency:
2.4 GHz: EU/2400-2483.5MHz (CH1-CH13)
5 GHz: EU/5150-5250MHz (CH36-CH48)
EIRP Power (Max.):
2.4 GHz: 19.5 dBm 5 GHz: 22 dBm
Software Version: V1.0.0.X
Operating Frequency:
2.4 GHz: EU/2400-2483.5MHz (CH1-CH13)
5 GHz: EU/5150-5250MHz (CH36-CH48)
EIRP Power (Max.):
2.4 GHz: 19.67 dBm 5 GHz: 22.21 dBm Software Version: V1.0.0.X
USA hotline: 1-800-570-5892
Toll Free: Daily-9am to 6pm EST
AC1200 Whole Home Mesh WiFi System
Model Mesh5
Power 12V 1A
FCC ID V7TMESH5
IC 9034A-MESH5
MAC
SN
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This decive may not cause harmful interference.
(2) this decive must accept any interference received,
including interference that may cause undesired operation.
SSID:
NOVA_XXXX
Password:
12 V 1 A power
adapter
Done.
WAN/LAN
Mesh5 x 1
9 V 1 A power adapter x 2
Quick installation guidex1Ethernet cablex 1
Package contents
12 V 1 A power adapter x 1
Mesh3f x 2
RST
PWRLAN
WAN/LAN
Tips
CAN ICES-3(B)/NMB-3(B)
handled pursuant to European directive 2012/19/EU in order to be recycled
or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling
organization or to the retailer when he buys new electrical or electronic
equipment.

Onko teillä kysyttävää Tenda Nova MW5s ?

Kysy kysymys muilta Tenda Nova MW5s omistajilta täällä. Tarjoa selkeä ja kattava kuvaus ongelmastasi ja kysymyksestäsi. Mitä paremmin esittelet ongelman ja kysymyksen, sitä helpompi muilla Tenda Nova MW5s omistajilla on tarjota sinulle hyvä vastaus.

Tekniset tiedot

Tuotemerkki Tenda
Malli Nova MW5s
Tuote Tukiasema
EAN 6932849428063
Kieli Englanti
Tuoteryhmä Tukiasemat
Tiedoston tyyppi PDF
Suunnittelu
Tuotetyyppi Kannettava reititin
Tuotteen väri Valkoinen
Merkkivalo
Tuotteen väri Valkoinen
Uudelleenkäynnistyspainike
Sertifiointi FCC, CE, RoHS, EAC, IC
Sijoitus Taulukko
LED-merkkivalot Signal strength, System
WAN-yhteys
Ethernet WAN
DSL WAN
SIM-korttipaikka
3G/4G USB -modeemin yhteensopivuus
Langattoman lähiverkon ominaisuudet
Wi-Fi-taajuus Kaksitaajuus (2, 4 GHz/5 GHz)
Wi-Fi-standardi Wi-Fi 5 (802.11ac)
WLAN-tiedonsiirtonopeus (maks.) 867Mbit/s
WLAN-tiedonsiirtonopeus (1. kaista) 300Mbit/s
WLAN-tiedonsiirtonopeus (2. kaista) 867Mbit/s
Wi-Fi-standardit 802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac)
Antenni
Antennityyppi Sisäinen
Antennin vahvistustaso (maks.) 3dBi
Antennien määrä 2
Antennityyppi Sisäinen
Antennin vahvistustaso (maks.) 3dBi
Antennien määrä 2
Ympärisäteilevä
Integrated antenna
Verkko
Ethernet LAN
Ethernet LAN -käyttöliittymän tyyppi Gigabitti Ethernet
Ethernet LAN -datanopeudet 10, 100, 1000Mbit/s
Kaapelitekniikka 10/100/1000Base-T(X)
Verkkostandardit IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11k, IEEE 802.11n, IEEE 802.11r, IEEE 802.11v, IEEE 802.3, IEEE 802.3u
Portin uudelleenohjaus
SSID-based VLAN assignment
Staattinen reitti
VPN-tuki IPsec pass through, PPTP pass through, L2TP pass through
Ominaisuudet
Päivitettävä Firmware
Sertifiointi FCC, CE, RoHS, EAC, IC
Ethernet LAN -datanopeudet 10, 100, 1000Mbit/s
Verkkostandardit IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11k, IEEE 802.11n, IEEE 802.11r, IEEE 802.11v, IEEE 802.3, IEEE 802.3u
2,4 GHz
5 GHz
867Mbit/s
300Mbit/s
Tiedonsiirron enimmäisnopeus 1200Mbit/s
MIMO
MIMO-tyyppi Multi User MIMO
Mobiili verkostoituminen
3G
4G
Virranhallinta
Virtalähteen malli DC
AC-syöttöjännite 100 - 240V
AC-syöttötaajuus 50/60Hz
Ulostulojännite 12V
Lähtövirta 1A
Power over Ethernet -tuki
Ulostulojännite 12V
Lähtövirta 1A
Power over Ethernet -tuki
Tulojännite 100 - 240V
Syötteen taajuus 50/60Hz
Syöttöjännite 0.6A
Ympäristöolosuhteet
Käyttölämpötila (T-T) 0 - 40°C
Varastointilämpötila -40 - 70°C
Käytön suhteellinen kosteus (H-H) 10 - 90
Säilytysympäristön kosteus 5 - 90
Käyttölämpötila (T-T) 0 - 40°C
Varastointilämpötila -40 - 70°C
Käytön suhteellinen kosteus (H-H) 10 - 90
Säilytysympäristön kosteus 5 - 90
Liitettävyys
Ethernet LAN (RJ-45) -portit 2
USB-portti
Muistikorttipaikat
DC-tulojakki
Ethernet LAN (RJ-45) -portit 2
DC-tulojakki
USB 2.0 -porttien määrä 0
WAN-portti Ethernet (RJ-45)
Paino ja mitat
Tuotteen leveys 91mm
Tuotteen syvyys 91mm
Tuotteen korkeus 93mm
Tuotteen leveys 91mm
Tuotteen syvyys 91mm
Tuotteen korkeus 93mm
Hallintaominaisuudet
Uudelleenkäynnistyspainike
Päivitettävä Firmware
Suojaus
Tietoturva-algoritmit WPA2-PSK
Palomuuri
Palomuurisuojaus UDP flood attack defence, TCP flood attack defence, ICMP flood attack defence
Vierailijan käyttöoikeus
Tietoturva-algoritmit WPA2-PSK
VPN-tuki IPsec pass through, PPTP pass through, L2TP pass through
SSID broadcast
Pakkaustiedot
Sisältyvien tuotteiden lukumäärä 3
Pakkaustyyppi Laatikko
Virtalähde mukana
Sisältää johdot LAN (RJ-45)
Pika-asennusopas
Sisältyvien tuotteiden lukumäärä 3
Pakkaustyyppi Laatikko
Virtalähde mukana
Sisältää johdot LAN (RJ-45)
Protokollat
DHCP-asiakas
DHCP serveri
Universal Plug and Play (UpNP)
DHCP-asiakas
DHCP serveri
Universal Plug and Play (UpNP)
Muut ominaisuudet
Palomuurisuojaus UDP flood attack defence, TCP flood attack defence, ICMP flood attack defence
Suorituskyky
Yhteensopivat käyttöjärjestelmät Android 4.0+, iOS 8+