Vivanco Viv.Control 3

Vivanco Viv.Control 3 käyttöohje

  • Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Tel:+49 (0)4102 231235,
    Fax: +49(0)4102 231444, e-Mail: hotline@vivanco.de 1
    Vivanco Viv.Control 3 & 5 Universal Controller
    1.
    2.
    3.
    = SETUP (3 s) = Set
    4.
    = TV
    5.
    = 1 Set: XXX, e.g. 1 = 1XX
    6.
    = 5; Set: XXX, e.g. 5 = 15X
    7.
    = 2 Set: XXX, e.g. 2= 152
    (GB) Instructions
    Viv.Control 3 + 5
    remote control for almost all TV, audio, video and other
    infrared-controllable equipment
    1 Inserting the batteries
    Open the battery flap on the back of the remote control, s. Fig.1.
    – press the tongue lightly upwards, then insert 2 alkaline AAA
    batteries. Check that the polarity markings on the batteries and
    in the battery compartment are correctly lined up (+=+), then
    close the flap carefully. – Always use undamaged batteries.
    2 Setting label
    Attach the enclosed label in your language to the back of the
    VivControl so that you can still set the remote control should
    these instructions not be available.
    3 Adapting to appliances
    In order to control your appliances you must adapt or set the
    remote control to them. There are three ways of doing so: direct
    control code entry, code search or learning the button functions
    of original remote controls.
    If your VivControl does not understand you it blinks rapidly
    several times. Each understood entry is confirmed by an
    appliance button blinking once briefly.
    3.1 Direct control code entry using the enclosed list
    Example: setting to control a Panasonic television set:
    3.1.1 The enclosed list gives, for example, the Panasonic
    Code 152.
    Please make sure you have selected the correct list for
    television sets (TV).
    3.1.2 To prepare code entry, keep the
    SETUP button
    pressed until the lamp (LED) lights constantly.
    3.1.3 Then press the required appliance button, e.g.
    TV,
    and the number buttons (e.g. 1 5 2) in sequence.
    3.1.4 Once the numbers have been entered the button lamp
    goes out and the remote control is ready to control your
    appliance.
    3.1.5 Finally, test the control code setting by trying to control (in
    this example) your television set. If it does not work at all or not
    correctly try a different code from the list or the code search (see
    below).
    3.1.6 How to set the remote control for other appliances is
    described in part 3.1. ff. Instead of the TV appliance button,
    press another button, e.g. VCR, SAT, CD, CBL, HOME).
    Vivanco VivControl remote controls are TV+ remote controls, i.e.
    under TV you can only set television sets or video projectors,
    but any other appliance under the other appliance buttons.
    The button decriptions SAT, ASAT (analog sat receiver), DSAT
    (digital sat receiver), VCR, etc. are intended only for easier
    orientation.

Onko teillä kysyttävää Vivanco Viv.Control 3 ?

Kysy kysymys muilta Vivanco Viv.Control 3 omistajilta täällä. Tarjoa selkeä ja kattava kuvaus ongelmastasi ja kysymyksestäsi. Mitä paremmin esittelet ongelman ja kysymyksen, sitä helpompi muilla Vivanco Viv.Control 3 omistajilla on tarjota sinulle hyvä vastaus.

Katso täältä ilmaiseksi Vivanco Viv.Control 3 manuaalia. Oletko lukenut manuaalin, mutta se ei vastaa kysymykseesi? Tällöin voit kysyä kysymyksen tällä sivustolla muilta Vivanco Viv.Control 3 omistajilta.

Tekniset tiedot

Tuotemerkki Vivanco
Malli Viv.Control 3
Tuote Kaukosäädin
EAN 4008928100693
Kieli Hollantilainen, Englanti, Saksa, Ranska, Espanja, Italialainen, Portugali, Tanska, Puola, Venäjä, Unkari
Tiedoston tyyppi PDF
Suorituskyky
Tapahtumien ohjelmoija/muistuttaja
On/off-kytkin
Suunnittelu
Tuotteen väri Hopea

Myynnissä

    Liittyvät tuotteet

    Kaukosäädin Vivanco